Power windows

Power windows  - Windows - Instruments and controls - Infiniti G Owners Manual - Infiniti G

WARNING
• Make sure that all passengers have their hands, etc. inside the vehicle while it is in motion and before closing the windows.
Use the window lock switch to prevent unexpected use of the power windows.
• Do not leave children unattended inside the vehicle. They could unknowingly activate switches or controls and become trapped in the window. Unattended children could become involved in serious accidents.

The power windows operate when the ignition switch is in the ON position or for about 45 seconds after the ignition switch is pushed to the OFF position. If the driver’s or front passenger’s door is opened during this period of about 45 seconds, power to the windows is canceled.

1. Driver side window2. Front passenger side window3. Rear left passenger side window (Sedan only)4. Rear right passenger side window (Sedan only)5. Window lock button

1. Driver side window
2. Front passenger side window
3. Rear left passenger side window (Sedan only)
4. Rear right passenger side window (Sedan only)
5. Window lock button

Main power window switch (driver’s side)

To open or close the window, push down A or pull up B the switch and hold it.

The main switch (driver side switches) will open or close all the windows.

Locking passengers’ windows

When the lock button C is pushed in, only the driver side window can be opened or closed. Push it in again to cancel.

Passenger side power window switch

Passenger side power window switch

The passenger side switch will open or close only the corresponding window. To open or close the window, push down or pull up the switch and hold it.

Automatic operation (for front door windows or all door windows)

Automatic operation (for front door windows or all door windows)

To fully open or close the window, completely push down or pull up the switch and release it; it need not be held. The window will automatically open or close all the way. To stop the window, just push or lift the switch in the opposite direction.

A light push or pull on the switch will cause the window to open or close until the switch is released.

Auto reverse function

WARNING
There are some small distances immediately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., inside the vehicle before closing the window.

If the control unit detects something caught in the window as it is closing, the window will be immediately lowered.

The auto reverse function can be activated when the window is closed by automatic operation when the ignition switch is in the ON position or for 45 seconds after the ignition switch is pushed to the OFF position.

Depending on the environment or driving conditions, the auto reverse function may be activated if an impact or load similar to something being caught in the window occurs.

Automatic adjusting function (Coupe)

CAUTION
When the battery cable is removed from the battery terminal, do not close either of the front doors. The automatic window adjusting function will not work and the side roof panel may be damaged.

The power window has an automatic adjusting function. When the door is being opened, the window is automatically lowered slightly to avoid contact between the window and the side roof panel. When the door is closed, the window is automatically raised slightly.

While the automatic adjusting function does not work, the window will be controlled as follows: . When the door is opened, the window lowers for approximately 2 seconds.

• While the door is open, the window cannot be raised.

If the windows do not close automatically

If the power window automatic function (closing only) does not operate properly, perform the following procedure to initialize the power window system.

1. Push the ignition switch to the ON position.

2. Close the door.

3. Open the window completely by operating the power window switch.

4. Pull the power window switch and hold it to close the window, and then hold the switch more than 3 seconds after the window is closed completely.

5. Release the power window switch.

Operate the window by the automatic function to confirm the initialization is complete.

6. Perform steps 2 through 5 above for other windows.

If the power window automatic function does not operate properly after performing the procedure above, have your vehicle checked by an INFINITI retailer.

    See also:

    Removing spots
    Remove tar and oil spots, industrial dust, insects, and tree sap as quickly as possible from the surface of the paint to avoid lasting damage or staining. Special cleaning products are available at an ...

    Floor mats
    WARNING To avoid potential pedal interference that may result in a collision or injury: ► NEVER place a floor mat on top of another floor mat in the driver front position. ► U ...

    Cargo light
    The cargo light switch has three positions: ON 1 , center 2 and OFF 3 . ON position When the switch is in the ON position 1 , the cargo light will illuminate. Center position When the sw ...